This beginner article provides details with regard to the basics of setting up a Linux firewall using the iptables tool. It's important to note that configuring firewalls is slightly different depending on which flavour you use.
If you are just starting out and need to enable a firewall on your Linux system, I suggest you try a basic tool such as lokkit (which is available in major flavours including Fedora/RedHat and Ubuntu). It is a very simple tool that walks you through a configuration. To use this, run the command: gnome-lokkit
You may also be interested in a graphical tool, rather than using the command line to make changes to the iptables. If you prefer a graphical tool, there are many available on the Internet. Start with a visit to freshmeat.net.
Introduction to iptables
For those who don't know or are not aware, iptables is the Linux tool that controls network packets, allowing you to perform very fine grained control of network related transactions through a set of rules. The tool itself has been around for quite a while, and is based on Rusty Russell's excellent work.
But before you start creating rules using the iptables command, you also need to be aware that any rules you create will be lost if a server restart occurs. For this reason, most server administrators apply the set of iptable commands they use into a bash script that runs each time the server is restarted. With some flavours, you can also run a command set like this: service iptables save. This ensures that your configuration is saved and is automatically loaded upon bootup.
To use iptables, you apply rules to network packets that are either inbound (INPUT), outbound (OUTPUT), or being forwarded through your server (FORWARD). This is very important to understand.
To view the rules that are currently applied to your server, type the command: iptables -L
Basics of iptables
Creating properly functioning firewall rules is dependent upon your knowledge of what your server is doing.
For a secure server, it is best to establish rules that will DENY all incoming traffic. Once you do so, then you can make explicit rules that only allow exceptions such as for port 80 requests. This is far more comprehensive than trying to filter out things you want to block, because you could miss something important such as one open port that will be used to attack your server.
It is also beneficial to use iptables in conjunction with a hardware firewall, since this provides several levels of security and reduces the possibility that you missed something in your configuration.
Remember, that you can get all syntax details using the command: man iptables
Using firewall rules
Let's look at three sample rules and their core parts. Remember that some of the longer command lines wrap on the column, so make sure you type the entire command, not just the single line.
iptables -P INPUT DROP
This rule is very easy to understand and highly secure. It initiates the iptables tool, then sets a Policy (-P) for all inbound (INPUT) packets. The policy is to drop them all (DROP). Nice and secure. Note that you can only apply a policy to built in commands for iptables.
iptables -A INPUT -i lo -j ACCEPT
This rule is a bit more useful, in that it allows network traffic to occur on your local interface. Note that the append option (-A) is used, because this is not part of the built in policies. The new rule is appended to all inbound (INPUT) packets that are going to the interface (-i) local (lo). The rule is to allow all these packets (-j ACCEPT). Often if you run into problems with configuring installed applications, it begins with ensuring you allow local host connectivity, as shown.
This command also appends (-A) a rule to all inbound (INPUT) packets that are coming through the ethernet card interface (-i eth0). But it only applies to packets that use the TCP protocol (-p tcp). It is specific to any such packets going to the designated port 80 (--dport 80), and is set to allow them to pass (-j ACCEPT).
If you put all three of these rules together into one script you have:
a server that will block every inbound connection
but it allows for internal host connectivity through local
while it also allows port 80 tcp requests that are inbound to also go through
Notice that you can also get finer grain control by designating a specific IP. For example:
The options are truly limitless, but you need to be careful. Below is a basic script you may find useful for beginning your firewall rule settings. When copying this script remember the longer commands are broken into several lines:
# Logging for any failed packets for troubleshooting use
iptables -A INPUT -j LOG --log-prefix "INPUT: "
Hopefully this brief introduction to firewalls helps you identify key rules that can make a more secure server. In the next issue, I will share the list of the most essential system administrator commands.
This brief opinion piece should not be construed as factual information, and only contains the opinions and personal experiences of the author at the time of publication.
Microsoft, Microsoft Windows are trademarks or registered trademarks of Microsoft Corporation both in the United States and Internationally. All other trademarks or registered trademarks in this opinion piece belong to their respective owners.
LINUX SECURITY RELATED ARTICLES Copyright 2009-2010 ReallyLinux.com All Rights Reserved.
Linux is a registered trademark of Linus Torvalds.
All other trademarks and registered trademarks on this entire
web site are owned by their respective companies. This
site is not related or affiliated with any other sites.